Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on July 30, 2007.
As of Tuesday, September 17th, 2024 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModels
6138HKR, 6138-1HKR, 91671FLT, 912005-2007 4.6L Mustang GT

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-115-17
  • Executive Order 115-17 / D115-17
  • ARB # D-115-17
  • Executive Order No: D-115-17
  • C.A.R.B. No. D-115-17
  • Resolution D-115-17
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-115-17 PDF

D-115-17 Document:


CARB_D-115-17

                                   State of California
                               AIR RESOURCES BOARD


                             EXECUTIVE ORDER D-115-17

                      Relating to Exemptions Under Section 27156
                                   of the Vehicle Code


                            Holley Performance Products, Inc.
                                 Ford Exhaust Header Kit

Pursuant to the authority vested in the Air Resources Board by Section 271 56 of the
Vehicle Code; and

Pursuant to the authority vested in the undersigned by Section 39515 and Section
39516 of the Health and Safety Code and Executive Order G-02-003;

IT IS ORDERED AND RESOLVED: That the installation of the Ford Exhaust Header
Kit manufactured and marketed by Holley Performance Products, Inc. of 1801
Russellville Road, P.O. Box 10360, Bowling Green, KY 42101-7360, has been found
not to reduce the effectiveness of required motor vehicle pollution control devices
and, therefore, is exempt from the prohibitions of Section 27156 of the Vehicle Code
for the Ford passenger cars and trucks listed in Exhibit A.

The Ford Exhaust Header Kit consists of tubular, short-length exhaust manifolds with
a 4-into-I configuration, and the corresponding asserr~blyhardware. The manifolds
replace the original exhaust manifolds upstream of the stock catalytic converters.
The exhaust gas recirculation sensor is removed from the stock manifold and
installed on a similar location on the replacement header. All other emission-related
components are in their stock location. The header kit is available in either painted
steel or ceramic-coated steel.

This Executive Order shall not apply to any Ford Exhaust Header Kit advertised,
offered for sale, sold with, or installed on a new motor vehicle prior to or concurrent
with transfer to an ultimate purchaser.

This Executive Order is valid provided that the installation instructions for the Ford
Exhaust Header Kit will not recommend tuning the vehicle to specifications different
from those of the vehicle manufacturer.

Changes made to the design or operating conditions of the devices, as exempted by
the Air Resources Board, that adversely affect the performance of a vehicle's
pollution control system shall invalidate this Executive Order.


Marketing of these devices using any identification other than that shown in this
Executive Order or marketing of this device for an application other than those listed
in this Executive Order shall be prohibited unless prior approval is obtained from the
Air Resources Board.

This Executive Order does not constitute any opinion as to the effect that the use of
these devices may have on any warranty either expressed or implied by the vehicle
manufacturer.

This exemption is issued based on submitted emissions test data from an
independent laboratory on a 2007 model year Ford Mustang passenger car (Test
Group 7FMXV04.76VBB) certified to the Low Emission Vehicle II Ultra Low Emission
Vehicle (LEV II ULEV) standards:

Federal Test Procedure:

                                               NMOG         a        NOx
Standards (glmi)                               0.040        1.7      0.05
Device (glrni) with df's applied               0.033        0.5      0.03
Additive d f s (50k)                           0.002        0.1      0.01

Test results showed that the Ford Exhaust Header Kit when installed on the vehicle
did not cause exhaust emissions to exceed the applicable emission standards during
the Cold Start Federal Test Procedure. This Executive Order is also based on the
On-Board Diagnostic II (OBD Il) testing conducted on the same test vehicle. The
Ford Exhaust Header Kit when installed on the test vehicle did not affect the vehicle's
ability to perform its OBD II monitoring.

In addition, the Air Resources Board reserves the right in the future to review this
Executive Order and the exemption provided herein to assure that the exempted add-
on or modified part continues to meet the standards and procedures of Title 13,
California Code of Regulations, Section 2222, et seq.

THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A.CERTIFICATION,
ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY
THE AIR RESOLIRCES BOARD OF ANY CLAIMS OF THE APPLICANT
CONCERNING AN-TI-POLLU-I-ION BENEFITS OR ANY ALLEGED BENEFITS OF
THE FORD EXHAUST HEADER KIT.

No claims of any kind, such as "Approved by the Air Resources Board" may be made
with respect to the action taken herein in any advertising or other oral or written
communication.

Violation of any of the above conditions shall be grounds for revocation of this order.
The order may be revoked only after a ten day written notice of intention to revoke


    HOLLEY PERFORMANCE PRODUCTS, INC. - FORD EXHAUST HEADER KIT - D-115-17


the order, in which period the holder of the order may request in writing a hearing to
contest the proposed revocation. If a hearing is requested, it shall be held within ten
days of receipt of the request and the order may not be revoked until a determination
is made after the hearing that grounds for revocation exist.


Executed at El Monte, California, this   30 day of July 2007.


                                         Annette Hebert, Chief
                                         Mobile Source Operations Division




    HOLLEY PERFORMANCE PRODUCTS, INC. - FORD EXHAUST HEADER KIT - D-115-17


                                                           Exhibit A
                                                       (E.O.# D-115-17)

                                                                                       Part Number
Model Year               Ford Model           Engine   Hooker Brand   Flowtech Brand   Summit Brand   Dynomax Brand   Jegs Brand

             Ford Mustang GT                             6138HKR        91671FLT
             Ford Mustang GT                            6138-1HKR      91671-1FLT
             F-15012501350                               6854HKR
             F-15012501350                              6854-1HKR
             F-1501250 Bronco 2WDl4W D                                  91627FLT         SUM-G9035
             F-1501250 Bronco 2WDl4WD                                  91627-1FLT
             F-1501250 Bronco, 351W 2WDl4WD                             91628FLT         SUM-G9036
             F-1501250 Bronw, 351W 2WDl4WD                             91628-1FLT
             F-1501250 Bronco. 351W                                     91668FLT
             F-1501250 Bronco, 351W                                    91688-1FLT
             Expedition, F-1501250                       6856HKR        91669FLT
             Expedition, F-1501250                      6856-1HKR      91669-1FLT
             Expedition, F-1501250                       6855HKR        91670FLT
             Expedition, F-1501250                      6855-1HKR      91670-1FLT



Document Created: 2008-03-26 15:29:37
Document Modified: 2008-03-26 15:29:37

Previous E.O. D-115-16 | Previous E.O. D-114 | Next E.O. D-115-18 | Next E.O. D-116