Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on July 8, 2008.
As of Thursday, December 13th, 2018 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModelsRemarks
D760-0020, D760-00212006 to 2008 model year BMW M5 and M6 vehiclesThe High Flow Cold Air Intake System is a modification made to the stock air filter housing bottom (dirty air side). A hole is cut and tubing is attached to capture cold air from the bottom of the vehicle. No changes are made to the stock air flow meter or housing lid.

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-176-34
  • Executive Order 176-34 / D176-34
  • ARB # D-176-34
  • Executive Order No: D-176-34
  • C.A.R.B. No. D-176-34
  • Resolution D-176-34
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-176-34 PDF

D-176-34 Document:



                                    State of California
                                AIR RESOURCES BOARD

                              EXECUTIVE ORDER D—176—34

                       Relating to Exemptions Under Section 27156
                                  of the California Vehicle Code

                                  Dinan Engineering, Inc.
                             High Flow Cold Air Intake System

Pursuant to the authority vested in the Air Resources Board by Section 27156 of the
Vehicle Code; and

Pursuant to the authority vested in the undersigned by Section 39515 and Section 39516
of the Health and Safety Code and Executive Order G—02—003;

IT IS ORDERED AND RESOLVED: That the installation of the High Flow Cold Air Intake
System, produced and marketed by Dinan Engineering, Inc. of 865 Jarvis Drive, Morgan
Hill, California 95037, has been found not to reduce the effectiveness of the applicable
vehicle pollution control systems and, therefore, is exempt from the prohibitions of Section
27156 of the Vehicle Code for the following 2006 to 2008 model year BMW MS and M6
vehicles.

Part No.       Engine Displacement        Model Year            Model
D760—0020            5.0L                 2006 to 2008           MS5
D760—0021            5.0L                 2006 to 2008           M6 and M6 Convertible

The High Flow Cold Air Intake System is a modification made to the stock air filter
housing bottom (dirty air side). A hole is cut and tubing is attached to capture cold air
from the bottom of the vehicle. No changes are made to the stock air flow meter or
housing lid.

This Executive Order is valid provided that the installation instructions for the High Flow
Cold Air Intake System will not recommend tuning the vehicle to specifications different
from those of the vehicle manufacturer.

Changes made to the design or operating conditions of the High Flow Cold Air Intake
System, as exempt by the Air Resources Board, which adversely affect the performance
of the vehicle‘s pollution control system shall invalidate this Executive Order.

This Executive Order shall not apply to any High Flow Cold Air Intake System advertised,
offered for sale, sold with, or installed on a new motor vehicle prior to or concurrent with
transfer to an ultimate purchaser.

Marketing of the High Flow Cold Air Intake System using any identification other than that
shown in this Executive Order or marketing of the High Flow Cold Air Intake System for
an application other than those listed in this Executive Order shall be prohibited unless
prior approval is obtained from the Air Resources Board.


                                             7.

This Executive Order does not constitute any opinion as to the effect the use of the High
Flow Cold Air Intake System units may have on any warranty either expressed or implied
by the vehicle manufacturer.

This Executive Order is granted based on a prior Executive Order for Dinan       _
Engineering, Inc. (D—176—32) which exempted the High Flow Cold Air Intake System on
BMW vehicles certified to the Low Emission Vehicle II Ultra Low Emission Vehicle
(LEV 1| ULEV) emission standards.

Similar effect on vehicle emissions is expected with the installation of the High Flow Cold
Air Intake on vehicles listed in this Executive Order.

The Air Resources Board reserves the right in the future to review this Executive Order
and the exemption provided herein to assure that the exempted add—on or modified part
continues to meet the standards and procedures of Title 13, California Code of
Regulations, Section 2222, et seq.

THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION,
ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE
AIR RESOURCES BOARD OF ANY CLAIMS OF THE APPLICANT CONCERNING
ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF DINAN
ENGINEERING, INC.‘S HIGH FLOW COLD AIR INTAKE SYSTEM.

No claim of any kind, such as "Approved by the Air Resources Board", may be made with
respect to the action taken herein in any advertising or other oral or written
communication.

Violation of any of the above conditions shall be grounds for revocation of this order. The
order may be revoked only after a ten—day written notice of intention to revoke the order,
in which period the holder of the order may request in writing a hearing to contest the
proposed revocation. If a hearing is requested, it shall be held within ten days of receipt
of the request and the order may not be revoked until a determination is made after the
hearing that grounds for revocation exist.

Executed at El Monte, California, this       g           day of July 2008.



                                 Annette Hebert, Chief
                                 Mobile Source Operations Division




  DINAN ENGINEERING, INC. — HIGH FLOW COLD AIR INTAKE SYSTEM — D—176—34



Document Created: 2008-07-23 13:27:23
Document Modified: 2008-07-23 13:27:23

Previous E.O. D-176-33 | Previous E.O. D-175 | Next E.O. D-176-35 | Next E.O. D-177