Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on September 4, 1997.
As of Friday, October 18th, 2019 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModels
301001995-1997 Camaro/Firebird 5.7L

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-187-8
  • Executive Order 187-8 / D187-8
  • ARB # D-187-8
  • Executive Order No: D-187-8
  • C.A.R.B. No. D-187-8
  • Resolution D-187-8
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-187-8 PDF

D-187-8 Document:



                                                                                        (Page 1 of 2)

                                                   State of California
                                             AIR RESOURCES BOARD

                                          EXECUTIVE ORDER D—187—8
                                    Relating to Exemptions Under Section 27156
                                                 of the Vehicle Code

                                          SLP ENGINEERING, INC.
                                   STAINLESS STEEL EXHAUST MANIFOLD

Pursuant to the authority vested in the Air Resources Board by Section 27156 of the Vehicle Code; and

Pursuant to the authority vested in the undersigned by Sections 39515 and 39516 of the Health and Safety Code and
Executive Order G—45—9;

IT IS ORDERED AND RESOLVED: That the installation of the Stainless Steel Exhaust Manifold, P/N 30100,
manufactured by SLP Engineering, Inc. of 1501 Industrial Way North, Toms River, New Jersey 08755, has been
found not to reduce the effectiveness of the applicable vehicle pollution control system and, therefore, is exempt
from the prohibitions of Section 27156 of the Vehicle Code for all 1995—97 Camaro/Firebird vehicles equipped with
the LT—1 5.7 liter gasoline engine and dual catalytic converters.

The Stainless Steel Exhaust Manifold is a direct replacement cast stainless steel exhaust manifold identical to the
stock cast iron manifold. The oxygen sensor is located at the collector of each manifold. The new manifold bolts to
all the stock General Motors components including the factory connecting pipes with no modifications required to
any sensors.

This Executive Order is valid provided that installation instructions for this kit will not recommend tuning the
vehicles to specifications different from those of the vehicle manufacturer.

Changes made to the design or operating conditions of the devices, as exempt by the Air Resources Board, which
adversely affect the performance of a vehicle‘s pollution control system shall invalidate this Executive Order.

Marketing of this device using any identification other than that shown in this Executive Order or marketing of this
device for an application other than those listed in this Execitive Order shall be prohibited unless prior approval is
obtained from the Air Resources Board.

This Executive Order does not constitute any opinion as to the effect the use of the device may have on any warranty
either expressed or implied by the vehicles manufacturer.

THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION,
APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF CLAIMS
OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF
SLP ENGINEERING, INC.‘S STAINLESS STEEL EXHAUST MANIFOLD .

No claim of any kind, such as "Approved by the Air Resources Board", may be made with respect to the action
taken herein in any advertising or other oral or written communication.


SLP Engineering, Inc.                                                                Executive Order D—187—8
Stainless Steel Exhaust Manifold                                                     (Page 2 of 2)




Violation of any of the above conditions shall be grounds for revocation of this order. The order may be revoked
only after ten day written notice of intention to revoke the order, in which period the holder of the order may request
in writing a hearing to contest the proposed revocation. If a hearing is requested, it shall be held within ten days of
receipt of the request and the order may not be revoked until a determination after hearing that grounds for
revocation exist.

Executed at El Monte, Callrfomia, this 2      day of September 1997.




                                                                  R. B. Aummerfield,
                                                                  Mobile Source Operfitions Division



Document Created: 2005-09-01 12:45:55
Document Modified: 2005-09-01 12:45:55

Previous E.O. D-187-7 | Previous E.O. D-186 | Next E.O. D-187-9 | Next E.O. D-188