Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on May 8, 1995.
As of Tuesday, February 4th, 2025 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModels
020-01-69361983-1995 Ford F150, F250, F350 p/u trucks equipped with a 7.3L diesel engine, front tank and standard bed

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-288-4
  • Executive Order 288-4 / D288-4
  • ARB # D-288-4
  • Executive Order No: D-288-4
  • C.A.R.B. No. D-288-4
  • Resolution D-288-4
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-288-4 PDF

D-288-4 Document:

CARB_D-288-4

(Page 1 of ?) State of California AIR RESOURCES BOARD EXECUTIVE ORDER D—288—4 Relating to Exemptions Under Section 27156 of the Vehicle Code TRANSFER FLOW, INC. REPLACEMENT FILL NECK KIT Pursuant to the authority vested in the Air Resources Board (ARB) by Section 27156 of the Vehicle Code; and Pursuant to the authority vested in the undersigned by Sections 39515 and 39516 of the Health and Safety Code and Executive Order G—45—9; IT IS ORDERED AND RESOLYED: That the installation of the Replacement Fill Neck Kit, manufactured by Transfer Flow, Inc. of 1444 Fortress Street, Chico, California 95926, has been found not to reduce the effectiveness of the applicable vehicle pollution control system, and therefore, the Replacement Fill Neck Kit is exempt from the prohibitions of Section 27156 of the Vehicle Code for installation on the vehicles listed in Exhibit A which is attached hereto and incorporated herein. This Executive Order (Order) is valid provided that installation instructions for the Replacement Fill Neck Kit will not recommend tuning the vehicle to specifications different from those submitted by Transfer Flow, Inc. Changes made to the design or operating conditions of the Replacement Fill Neck Kit, as exempt by the ARB, which adversely affect the performance of a vehicle‘s po]thion control system shall invalidate this Executive Order. Marketing of the Replacement Fill Neck Kit using an identification other than that shown in this Executive Order or for an application other than those listed in this Executive Order shall be prohibited unless prior approval is obtained from the ARB. In addition to the foregoing, the ARB reserves the right in the future to review this Executive Order and the exemption provided herein to assure that the exempted add—on or modified part continues to meet the standards and procedures of Title 13, California Code of Regulations, Section 2222 et seq. This Executive Order does not constitute any opinion as to the effect the use of the Replacement Fill Neck Kit may have on any warranty either expressed or implied by the vehicle manufacturer. THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF CLAIMS OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF TRANSFER FLOW, INC.‘S REPLACEMENT FILL NECK KIT.

TRANSFER FLOW, INC. EXECUTIVE ORDER D—288—4 REPLACEMENT FILL NECK KIT (Page 2 of 2) No claim of any kind, such as "Approved by the Air Resources Board", may be made with respect to the action taken herein in any advertising or other oral or written communication. Vialation of any of the above conditions shall be grounds for revocation of this Order. The Order may be revoked only after a ten—day written notice of intention to revoke the Order, in which period the holder of the Order may request in writing a hearing to contest the proposed revocation. If a hearing is requested, it shall be held within ten days of receipt of the request and the Order may not be revoked until a determination after the hearing that grounds for revocation exist. Executed at El Monte, California, this Sf iday of May 1995. . [. Summerfi AsSistant Division Chief Mobile Source Division

EXHIBIT A E.0. D—288—4 VEHICLE MODEL ENGINE KIT APPLICATION MAKE YEAR SIZE NUMBER DESCRIPTION Ford P/U 1983—95 7.3 L 020—01—6936 Front tank, F150, F250, F350 Diesel standard bed Ford P/U 1983—95 7.3 L 020—01—6927 Rear tank, dual F150, F250, F350 Diesel wheel bed Ford P/U 1983—95 4.9 L 020—01—6939 Front tank, F150, F250, F350 5.0 L standard bed 5.8 L 7.5 L Ford P/U 1983—95 4.9 L 020—01—6942 Rear tank, dual F150, F250, F350 5.0 L wheel bed 5.8 L 7.5 L Ford Cab Chassis 1987—95 7.3 L 020—01—8271 Front tank, F—Super Duty Diesel standard bed Ford Cab Chassis 1987—95 7.3 L 020—01—8290 Rear tank, dual F—Super Duty Diesel wheel bed Ford Cab Chassis 1987—95 7.5 L 020—01—8273 Front tank, F—Super Duty standard bed Ford Cab Chas§is 1987—95 7.5 L 020—01—8291 Rear tank, dual wheel bed


Document Created: 2005-09-01 12:44:02
Document Modified: 2005-09-01 12:44:02

Previous E.O. D-288-3 | Previous E.O. D-287 | Next E.O. D-288-5 | Next E.O. D-289