Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on January 2, 2015.
As of Wednesday, January 22nd, 2025 this Executive Order has not been overturned or superceeded.

Approved Parts

Part Number
See PDF

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-355-14
  • Executive Order 355-14 / D355-14
  • ARB # D-355-14
  • Executive Order No: D-355-14
  • C.A.R.B. No. D-355-14
  • Resolution D-355-14
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-355-14 PDF

D-355-14 Document:


CARB_D-355-14

                                    State of California
                                AIR RESOURCES BOARD

                              EXECUTIVE ORDER D—355—14

                       Relating to Exemptions Under Section 27156
                                  of the California Vehicle Code

                                    S&S Cycle, Inc.
                Original Equipment Specifications Gear Drive Camshafts
                           Part Numbers 106—4033 or 106—4385

Pursuant to the authority vested in the Air Resources Board by Section 27156 of the
Vehicle Code; and

Pursuant to the authority vested in the undersigned by Section 39515 and Section 39516
of the Health and Safety Code and Executive Order G—14—012;

IT IS ORDERED AND RESOLVED: That the installation of the Original Equipment
Specifications Gear Drive Camshafts, manufactured and marketed by S&S Cycle, Inc.,
14025 County Highway G, Viola, Wisconsin 54664, has been found not to reduce the
effectiveness of the applicable motorcycle pollution control systems and, therefore, is
exempt from the prohibitions of Section 27156 of the Vehicle Code for the following .
Harley—Davidson motorcycles listed in Exhibit A.

The Original Equipment Specifications Gear Drive Camshafts, designed to convert a
factory chain driven camshaft to a gear driven camshaft, includes the following main
parts: Part Number 106—4033, two factory replacement camshafts, inner and outer cam
drive gears, pinion shaft gear, and inner and outer camshaft bearings, part number
106—4385 includes the camshafts and inner drive gear only.

This Executive Order is valid provided that the installation instructions for the Original
Equipment Specifications Gear Drive Camshafts will not recommend tuning the
motorcycle to specifications different from those of the S&S Cycle, Inc.

Changes made to the design or operating conditions of the Original Equipment
Specifications Gear Drive Camshafts, as exempt by the Air Resources Board, which
adversely affect the performance of the motorcycle‘s pollution control system shall
invalidate this Executive Order.

This Executive Order is granted based on an engineering evaluation and information
supplied by S&S Cycle, Inc. on the Original Equipment Specifications Gear Drive
Camshafts. Comparisons made between the stock and modified parts, demonstrated
that the new camshafts retain the stock lift and duration, and S&S Cycle, Inc. claims
the Original Equipment Specifications Gear Drive Camshafts is a more durable part
due to the design which eliminates the plastic shoe ring on the chain tensioner.

The Air Resources Board reserves the right in the future to review this Executive
Order and the exemption provided herein to assure that the exempted add—on or
modified part continues to meet the standards and procedures of Title 13, California
Code of Regulations, Section 2222, et seq.


THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION,
ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY
THE AIR RESOURCES BOARD OF ANY CLAIMS OF THE APPLICANT
CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF
THE ORIGINAL EQUIPMENT SPECIFICATIONS GEAR DRIVE CAMSHAFTS.

Marketing of the Original Equipment Specifications Gear Drive Camshafts using any
identification other than that shown in this Executive Orderor marketing of the
Original Equipment Specifications Gear Drive Camshafts for an application other than
those listed in this Executive Order shall be prohibited unless prior approval is
obtained from the Air Resources Board.

No claim of any kind, such as "Approved by the Air Resources Board", may be made
with respect to the action taken herein in any advertising or other oral or written
communication.                                               —

Violation of any of the above conditions shall be grounds for revocation of this order.
The order may be revoked only after a ten—day written notice of intention to revoke
the order, in which period the holder of the order may request in writing a hearing to
contest the proposed revocation. If a hearing is requested, it shall be held within ten
days of receipt of the request and the order may not be revoked until a determination
is made after the hearing that grounds for revocation exist.

Executed at El Monte, California, this     Z        day of January 2015.




            Annette Hebert, Chief
            Emissions Compliance, Automotive Regulations and Science Division




  S&S CYCLE, INC. — ORIGINAL EQUIPMENT SPECIFICATIONS GEAR DRIVE
                         CAMSHAFTS —D—355—14


                                            Exhibit A
                            S&S Gear Drive Cam Kit PN Application List
                                                       Motorcycle Application
       Gear Drive Cam kit
                                            Make                          Model List
                                                                FLHP, FLHPEI, FLHP1, FLHR, FLHRCI,
                                    All 1999—2006 Harley—          FLHRI, FLHRI—Shrine, FLHRSE1,
                                      Davidson® Touring          FLHRSEI2, FLHRSI, FLHT, FLHTC,
                                       Models Originally         FLHTCI, FLHTCI—Shring, FLHTCS,
                                    Equipped With 1449cc          FLHTCSE2, FLHTCSEI, FLHTCUI,
PN 106—4033: Gear Drive Cam kit,     Engines, except 1999—      FLHTCUI—Shrine, FLHTCUSE, FLHTH,
  complete kit, "OES" cam grind     03 Fuel Injected Models       FLHTPI, FLHXI, FLTHCUI, FLTRI,
                                                                        FLTRSEl, FLTRSEl2


                                      All 1999—2005 Harley—       FXD, FXDC—A, FXDI, FXDL, FXDL1,
                                    Davidson® Dyna Models          FXDP, FXDS, FXDWG, FXDWG2,
                                    Originally Equipped With|     FXDWG3, FXDWGI, FXDX, FXDXI,
                                        1449cc engines                     FXDXT, FXFS




 PN 106—4385: Gear Drive Cams,                              FLSTCI, FLSTCI—A, FLSTFI, FLSTFIA,
                                     All 1999—2006 Harley—
Cams with inner Gears only, "OES"                           FLSTNI, FLSTSCI, FLSTSI, FLSTSI—A,
                                        Davidson® Softail
            cam grind                                       FXSI, FXST, FXSTB, FXSTBI, FXSTD,
                                        Models Originally
                                                           FXSTDE, FXSTDI, FXSTDI—A, FXSTDSE,
                                     Equipped With 1449cc
                                                             FXSTDSE2, FXSTI, FXSTNI, FXSTS,
                                            engines
                                                                          FXSTSI





Document Created: 2015-02-16 16:46:17
Document Modified: 2015-02-16 16:46:17

Previous E.O. D-355-13 | Previous E.O. D-354 | Next E.O. D-355-15 | Next E.O. D-356