Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on April 14, 2009.
As of Monday, November 11th, 2024 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModelsModificationRemarks
SUM-2272001986-1993 5.0L Ford MustangThrottle Body65mm (polish finish)

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-369-11
  • Executive Order 369-11 / D369-11
  • ARB # D-369-11
  • Executive Order No: D-369-11
  • C.A.R.B. No. D-369-11
  • Resolution D-369-11
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-369-11 PDF

D-369-11 Document:


CARB_D-369-11

                                   State of California
                               AIR RESOURCES BOARD

                             EXECUTIVE ORDER D-369-1I

                              Relating to Exemptions under
                            Section 27156 of the Vehicle Code

                 Trick Flow Specialties (aka Summit Racing Equipment)
                             Throttle Body and EGR Plate

Pursuant to the authority vested in the Air Resources Board by Section 27156 of the
Vehicle Code; and

Pursuant to the authority vested in the undersigned by Sections 39515 and 39516 of the
Health and Safety Code and Executive Order G-02-003;

IT IS ORDERED AND RESOLVED: That installation of the Throttle Body and EGR
Plate, manufactured by Professional Products of 12705 South Van Ness Avenue,
Hawthorne, California 90250, and marketed by Summit Racing Equipment of 285 West
Avenue, Tallmadge, Ohio 44278, has been found not to reduce the effectiveness of the
applicable vehicle pollution control systems, and therefore, is exempt from the
prohibitions in Section 27156 of the Vehicle Code for installation on the vehicles listed in
Attachment A.

The Throttle Body is a replacement throttle body designed with a larger diameter throttle
bore and throttle plate. The EGR Plate is a larger diameter EGR plate that is installed in
the stock location between the throttle body and intake manifold. lnstallation requires
the transfer of the stock throttle position sensor to the new throttle body. There are no
user adjustments other than engine idle speed, which is the same as stock.

This Executive Order is based on Cold-Start CVS-75 Federal Test Procedure tests and
Supplemental Federal Test Procedures conducted in support of Professional Products'
Executive Order 0-624.

If evidence provides the Air Resources Board with reasons to suspect that the Throttle
Body and EGR Plate will affect the durability of the emission control system,
Professional Products shall be required to submit durability data to show that the
durability of the vehicle emission control system is not, in fact, affected andlor that the
add-on or modified parts demonstrate adequate durability.

This Executive Order is valid provided that installation instructions for the Throttle Body
and EGR Plate do not recommend tuning the vehicles to specifications different from
those of the vet-~iclenianufacturer.

Changes made to the design or operating conditions of the Throttle Body and EGR
Plate, as exempt by the Air Resources Board, which adversely affect the performance
of the vehicles' emission control system, shall invalidate this Executive Order.


Marketing of the Throttle Body and EGR Plate using identification other than that shown
in this Executive Order or for an application other than that listed in this Executive Order
shall be prohibited unless prior approval is obtained from the Air Resources Board.

Exemption of the Throttle Body and EGR Plate shall not be construed as exemption to
sell, offer for sale, or advertise any component of the system as an individual device.

This Executive Order shall not apply to any Throttle Body and EGR Plate advertised,
offered for sale, sold with, or installed on a motor vehicle prior to or concurrent with
transfer to an ultimate purchaser.

This Executive Order does not constitute any opinion as to the effect the use of the
Throttle Body and EGR Plate may have on any warranty either expressed or implied by
the vehicle manufacturer.

No claim of any kind, such as "Approved by the Air Resources Board," may be made
with respect to the action taken herein in any advertising or other oral or written
communication.

In addition to the foregoing, the Air Resources Board reserves the right in the future to
review this Executive Order and the exemption provided herein to assure that the
exempted add-on or modified part continues to meet the standards and procedures of
California Code of Regulations, Title 13, Section 2222, et seq.

THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION,
ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE
AIR RESOURCES BOARD OF ANY CLAIMS OF THE APPLICANT CONCERNING
ANTI-POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF SUMMIT RACING
EQUIPMENT'S THROTTLE BODY AND EGR PLATE.

Violation of any of the above conditions shall be grounds for revocation of this Executive
Order. The Executive Order may be revoked only after a ten day written notice of
intention to revoke the Executive Order, in which period the holder of the Executive .
Order may request in writing a hearing to contest the proposed revocation. If a hearing
is requested, it shall be held within ten days of receipt of the request, and the Executive
Order may not be revoked until a determination is made after the hearing that grounds
for revocation exist.

Executed at El Monte, California, this     /Y      day of April 2009.




                                         Mobile Source Operations Division




         SUMNllT RACING EQUlPMElVT - THROTTLE BODY AND EGR PLATE - D-369-11


                                          Attachment A


                                     Summit ÿ acing Equipment

                                             Throttle Body

        Part Number           Model Year                               Model Specification

        SUM-227200            1986-1993            Mustang 5.OL V8 engine, 65mm (polish finish)

        SUM-227201            1986-1993            Mustang 5.OL V8 engine, 70mm (polish finish)

        SUM-227202            1986-1993            Mustang 5.OL V8 engine, 75mm (polish finish)

        SUM-227203            1986-1993            Mustang 5.OL V8 engine, 65mm (satin finish)

I       SUM-227204    1       1986-1993        1    us tang 5.OL V8 engine, 70mm (satin finish)      I
        SUM-227205            1986-1993            Mustang 5.OL V8 engine, 75mm (satin finish)

        SUM-227210            1994-1995            Mustang 5.OL V8 engine, 65mm (polish finish)
                                                                                     -   -




                                               I~ustang
                                                      5.OL V8 engine. 70mm (polish finish)

                                               l ~ u s t a 5.OL
                                                           n ~ V8 engine, 75mm (polish finish)

                                               l ~ u s t a 5.OL
                                                           n ~ V8 engine, 65mm (satin finish)

                                               I ~ u s t a 5.OL
                                                           n ~ V8 engine, 70mm (satin finish)

                                                I ~ u s t a 5.OL
                                                            n ~ V8 engine, 75mm (satin finish)

                                                I   Ford 4.6L V8 engine, 70mm (polish finish)

                                                l~ord
                                                    4.6L V8 engine, 75mm (polish finish)

                                                l ~ o r 4.6L
                                                        d    V8 engine, 70mm (satin finish)

                                                l~ord
                                                    4.6L V8 engine, 75mm (satin finish)

                                               EGR Plate

        Part Number           Model Year                               Model Specification

I       SUM-227500     (      1986-1993             usta tan^ 5.OL V8 engine, 65mm (polish finish)   I
                              1986-1993            I ~ u s t a 5.OL
                                                               n ~ V8 engine, 70mm (polish finish)   I
    I   SUM-227502        1   1986-1993            i ~ u s t a 5.OL
                                                               n ~ V8 engine, 75mm (polish finish)   I
        SUM-227503            1986-1993             Mustang 5.OL V8 engine, 65mm (satin finish)

        SUM-227504            1986-1993             Mustang 5.OL V8 engine, 70mm (satin finish)

        SUM-227505            1986-1993             Mustang 5.OL V8 engine, 75mm (satin finish)




             SUMMIT RACING EQUIPMENT - THROTTLE BODY AND EGR PLATE - D-369-11



Document Created: 2009-04-23 16:13:58
Document Modified: 2009-04-23 16:13:58

Previous E.O. D-369-10 | Previous E.O. D-368 | Next E.O. D-369-12 | Next E.O. D-370