Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on October 17, 1996.
As of Sunday, June 16th, 2019 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModels
50931986-1993 Ford Mustang 5.0L

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-374-2
  • Executive Order 374-2 / D374-2
  • ARB # D-374-2
  • Executive Order No: D-374-2
  • C.A.R.B. No. D-374-2
  • Resolution D-374-2
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-374-2 PDF

D-374-2 Document:



                                                               (Page 1 of 2)

                                State of California
                                AIR RESOURCES BOARD

                              EXECUTIVE ORDER D—374—2
                   Relating to Exemptions Under Section 27156
                               of the Vehicle Code

                              BASSANI MANUFACTURING
                     EQUAL LENGTH EXHAUST MANIFOLD ASSEMBLY

Pursuant to the authority vested in the Air Resources Board by Section 27156
of the Vehicle Code; and

Pursuant to the authority vested in the undersigned by Sections 39515 and
39516 of the Health and Safety Code and Executive Order G—45—9;

IT IS ORDERED AND RESOLVED:     That the installation of the Equal Length Exhaust
Manifold Assembly, manufactured by Bassani Manufacturing of 2900 E. La Jolla
Ave., Anaheim,   California 92806 has been found not to reduce the effectiveness
of the applicable vehicle pollution control system and, therefore,          is exempt
from the prohibitions of Section 27156 of the Vehicle Code for installation on
the following Ford Motor Company vehicles:

    Part #         Modei-Year         Vehicle _Model            Engine Size

     5093           1986—93            Mustangs                    5. OL

     5094           1994—95            Mustangs                    5.0L

     50150          1987—96             F—150                      5. 0L
                    1980—96             Bronco                     5. 0L

     58150          1987—96             F—150                      5. 81L
                    1987—96             Bronco                     5. 8L

     581508         1987—95             F—150                      5. 8L
                    1988—95             Bronco                     5.81

     581501         1993—95             F150 lightning             5.81

     58150L—1       1993—95             F150 lightning             5.81

     §5093SR—1      1986—93            Mustang motors              5.0L
                                        used as part of
                                        engine change

     5094SR—1       1994—95             Mustang motors     .       5. 0L
                                        used as part of
                                        engine change

The Equal Length Exhaust Manifold Assembly consist of a set of exhaust headers
manufactured out of 14 gage  mild steel. Factory connector pipes are utilized.

This Executive Order is valid \provided that installation instructions for
these headers will not recommend tuning the vehicle to specifications
different from those of the vehAcle manufacturer.

Changes made to the design or operating conditions of the headers,          as exempt
by the Air Resources Board, which‘adversely affect the performance of a
vehicle‘s pollution control system shall invalidate this Executive Order.

Marketing of these headers using any identification other than that shown in
this Executive Order or marketing of the headers for an application other than
those listed in this Executive Order shall be prohibited unless prior approval
is obtained from the Air Resources Board.

This Executive Order does not constitute any opinion as to the effect the use
of the headers may have on any warranty either expressed or implied by the
vehicle manufacturer.


BASSANI MANUFACTURING                                     EXECUTIVE ORDER E-374—2
EQUAL LENGTH EXHAUST MANIFOLD ASSEMBLY                              (Page i of 2)


THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION,
APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF
CLAIMS OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED
BENEFITS OF BASSANI MANUFACTURING‘S EQUAL LENGTH EXHAUST MANIFOLD ASSEMBLY.

No claim of any kind, such as "Approved by the Air Resources Board" may be
made with respect to the action taken herein in any advertising or other oral
or written communication.

Violation of any of the above conditions shall be grounds for revocation of
this order.  The order may be revoked only after ten day written notice of
intention to revoke the order, in which period the holder of the order may
request in writing a hearing to contest the proposed revocation.  If a hearing
is requested, it shall be held within ten days of receipt of the request and
the order may not be revoked until a determination after hearing that grounds
for revocation exist.

Executive Order D—374—1 dated October 17,   1996,   is hereby superseded and no
longer of any force or effect.

Executed at El Monte, California,



Document Created: 2005-09-01 12:45:33
Document Modified: 2005-09-01 12:45:33

Previous E.O. D-374-1 | Previous E.O. D-373 | Next E.O. D-374-3 | Next E.O. D-375