Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on June 15, 1999.
As of Tuesday, August 20th, 2019 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModelsModification
851112, 70-1312, 72C131293-95 Chrysler trucks equipped with a 5.2/5.9LSame as above

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-439-2
  • Executive Order 439-2 / D439-2
  • ARB # D-439-2
  • Executive Order No: D-439-2
  • C.A.R.B. No. D-439-2
  • Resolution D-439-2
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-439-2 PDF

D-439-2 Document:



                                                                                    (Page 1 of 2)


                                             State of California
                                       AIR RESOURCES BOARD

                                      EXECUTIVE ORDER D—439—2
                               Relating to Exemptions Under Section 27156
                                            of the Vehicle Code

                                   PACESETTER MARKETING, INC.
                                       EXHAUST HEADERS

Pursuant to the authority vested in the Air Resources Board by Section 27156 of the Vehicle Code; and

Pursuant to the authority vested in the undersigned by Sections 39515 and 39516 of the Health and Safety
Code and Executive Order G—45—9;

IT IS ORDERED AND RESOLVED: That the installation of the Exhaust Headers, manufactured by
Pacesetter Marketing, Inc. of 2841 West Clarendon, Phoenix, Arizona 85043, has been found not to reduce
the effectiveness of the applicable vehicle pollution control system and, therefore, is exempt from the
prohibitions of Section 27156 of the Vehicle Code for the following truck applications as listed below.

Manufacturer      Part #                                           Year

Chrysler          851112, 70—1312, 72C1312                         93—95 5.2/5.9L
                  851115, 70—1315, 7201315                         96—98 5.2/5.9L

                  70—1128, 72C1128                                 87—90 Jeep YJ w/ 258 cid
                  70—1129, 72C1129                                 91—97 Jeep YJ & TJ w/ 4.0L
                  70—1138, 7201138                                 97/98 Jeep TJ w/ 2.5L
                  70—1191, 72C1191                                 82—90 Jeep Cherokee w/ 4.0L
                  70—1131, 72C1131                                 72—80 Jeep CJ w/ 232 or 258 cid
                  70—1135, 7201135                                 81—86 Jeep CJ w/ 258 cid
                  70—1134                                          84—86 Jeep Cherokee w/ 2.8L
                  70—1130                                          65—71 Jeep CJ w/ 231 cid

General Motors     851118, 70—1318, 72C1318                        88—95 5.7L w/o air inj.
                  851119, 70—1319, 72C1319                         88—95 5.7L w/ air inj.
                  851120, 70—1320, 72C1320                         96—98 5.7L w/o air inj.
                  851121, 70—1321, 72C1321                         96—98 4.3L

Ford              851122, 70—1322, 7201322                         87—95 5.0L
                  851123, 70—1323, 72C1323                         87—95 5.8L

The following 1998 model—year General Motors and Chrysler engine families, certified to the TLEV or
LEV emission standard are excluded from this Executive Order: GM Trucks: WGMXAOQ4.3188,
WGMXTO4.3185, WGMXTO4.3187, WGMXA05.7185, WGMXA05.7186,
Chrysler Trucks: WCRXA0360H31, WCRXA0360H32, and WCRXA0360J31.

The Exhaust Headers are a direct replacement shorty style header manufactured out of 16 gage mild steel.
The installation of the header utilizes the use of the stock connecting pipes and does not require the
relocation of any sensor, except for Jeep models. Part #s that begin with "72C" are coated with a metallic—
ceramic compound.

The Exhaust Headers for the Jeep models are a long tube style header manufactured out of 16 gage mild
steel tubing. The location of the oxygen sensor is at the collector, similar to the stock configuration.
On vehicles where the existing oxygen sensor wire loom does not reach the new oxygen sensor location,
PaceSetter will provide a wire loom extension that will plug into the factory connector.


PACESETTER MARKETING, INC.                                                   Executive Order D—439—2
EXHAUST HEADERS                                                              (Page 2 of 2)


This Executive Order shall not apply to any Pacesetter Marketing, Inc. Exhaust Header advertised, offered
for sale, or sold with or installed on, a motor vehicle prior to or concutrent with transfer to an ultimate
purchaser.

This exemption is issued based on previously submitted emissions test data of a General Motors, Ford, and
Chrysler vehicle.

This Executive Orderis valid provided that installation instructions for this kit will not recommend tuning
the vehicles to specifications different from those of the vehicle manufacturer.

Changes made to the design or operating conditions of the devices, as exempt by the Air Resources Board,
which adversely affect the performance of a vehicle‘s pollution control system shall invalidate this
Executive Order.

Marketing of this device using any identification other than that shown in this Executive Order or
marketing of this device for an application other than those listed in this Executive Order shall be
prohibited unless prior approval is obtained from the Air Resources Board.

This Executive Order does not constitute any opinion as to the effect the use of the device may have on any
warranty either expressed or implied by the vehicles manufacturer.

THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION,
APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF
CLAIMS OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED
BENEFITS OF PACESETTER MARKETING, INC.‘S EXHAUST HEADERS .

No claim of any kind, such as "Approved by the Air Resources Board", may be made with respect to the
action taken herein in any advertising or other oral or written communication.

Violation of any of the above conditions shall be grounds for revocation of this order. The order may be
revoked only after ten day written notice of intention to revoke the order, in which period the holder of the
order may request in writing a hearing to contest the proposed revocation. If a hearing is requested, it shall
be held within ten days of receipt of the request and the order may not be revoked until a determination
after hearing that grounds for revocation exist.

Executive Order D—439—1, dated April 1998, is Eperseded and of no further force and effect.

Executed at El Monte, California, this        [5 day of J        1999.




                                          .     B.   Summerfield, Chief
                                         Mobile Source Operations Division



Document Created: 2005-09-01 12:42:04
Document Modified: 2005-09-01 12:42:04

Previous E.O. D-439-1 | Previous E.O. D-438 | Next E.O. D-439-3 | Next E.O. D-440