Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on October 30, 2003.
As of Friday, October 11th, 2024 this Executive Order has not been overturned or superceeded.

Approved Parts

ModelsModification
1997 through 2004 model-year Corvettes, excluding those under test groups 2GMXV05.7082, 3GMXV05.7082, and 4GMXV05.7082 with Z06 models.The Corvette Exhaust Header is manufactured out of 16 gage stainless steel. It is a shorty design that bolts up to the stock connecting pipes. The oxygen sensor is located at the collector of the header. Part nos. FCOR-0250 is applicable to 1997 through 1999 model-year Corvette, FCOR-0255 is applicable to 2000 model-year Corvette, and FCOR-0257 is applicable to 2001 through 2004 model-year Corvette.

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-506-2
  • Executive Order 506-2 / D506-2
  • ARB # D-506-2
  • Executive Order No: D-506-2
  • C.A.R.B. No. D-506-2
  • Resolution D-506-2
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-506-2 PDF

D-506-2 Document:

CARB_D-506-2

. State of California . AIR RESOURCES BOARD EXECUTIVE ORDER D—506—2 Relating to Exemptions Under Section 27156 of the Vehicle Code B&B Fabrication, Inc. Corvette Exhaust Header Pursuant to the authority vested in the Air Resources Board by Section 27156 of the Vehicle Code; and Pursuant to the authority vested in the undersigned by Section 39515 and Section 39516 of the Health and Safety Code and Executive Order G—02—003; IT 4S ORDERED AND RESOLVED: That the installation of the Corvette Exhaust Header, manufactured and marketed by B&B Fabrication, Inc., 23045 North 15th Avenue, Phoenix, Arizona 85027 has been found not to reduce the effectiveness of the applicable vehicle pollution control system and, therefore, is exempt from the prohibitions of Section 27156 of the Vehicle Code for 1997 through 2004 model—year Corvettes, excluding those under test _ groups 2GMXVO5.7082, 3GMXVO5.7082, and 4GMXV05.7082 with 206 models. The Corvette Exhaust Header is manufactured out of 16 gage stainless steel. It is a shorty design that bolits up to the stock connecting pipes. The oxygen sensor is located at the collector of the header. Part nos. FCOR—0250 is applicable to 1997 through 1999 model—year Corvette, FCOR—0255 is applicable to 2000 model—year Corvette, and FCOR—0257 is applicable to 2001 through 2004 model—year Corvette. This Executive Order is valid provided the installation instructions for the Corvette Exhaust Header will not recommend tuning the vehicle to specifications different from those of the vehicle manufacturer. This Executive Order shall not apply to any Corvette Exhaust Header advertised, offered for sale, sold with, or installed on a motor vehicle prior to or concurrent with transfer to an ultimate purchaser. v Changes made to the design or operating conditions of the Corvette Exhaust Header, as exempt by the Air Resources Board, which adversely affect the performance of the vehicle‘s . pollution control system shall invalidate this Executive Order. Marketing of the Corvette Exhaust Header using any identification other than that shown in this Executive Order or marketing of the Corvette Exhaust Header for an application other than those listed in this Executive Order shall be prohibited unless prior approval is obtained from the Air Resources Board. Exemption of the Corvette Exhaust Header shall not be construed as exemption to sell, offer for sale, or advertise any component of the kit as an individual device.

—2. This Executive Order does not constitute any opinion as to the effect the use of the Corvette Exhaust Header may have on any warranty either expressed or implied by the vehicle manufacturer. This Executive Orderis granted based on the emissions test data submitted by B&B Fabrication, Inc. on a 2000 General Motors Corvette, certified to the Low Emission Vehicle (LEV) emission standards. NMOG CO NOx HCHO Standards 0.075 3.4 0.2 0.015 device w/ dfs 0.052 1.5 017 0.002 Test results showedthat the Corvette Exhaust Header when installed on the vehicle did not cause tailpipe emissions to exceed the vehicle‘s applicable emission standards during a Cold Start CVS—75 Federal Test Procedure. This Executive Order is also based on the On Board Diagnostic l1 (OBD II) testing conducted on the same test vehicle. Test data showed that the Corvette Exhaust Header when installed on the vehicle did not affect the vehicle‘s ability to perform OBD I! monitoring. THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF ANY CLAIMS OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF B&B FABRICATION, INC.‘S CORVETTE EXHAUST HEADER. No claim of any kind, such as "Approved by the Air Resources Board", may be made with respect to the action taken herein in any advertising or other oral or written communication. Violation of any of the above conditions shall be grounds for revocation of this order. The order may be revoked only after a ten—day written notice of intention to revoke the order, in which period the holder of the order may request in writing a hearing to contest the proposed revocation. If a hearing is requested, it shall be held within ten days of receipt of the request and the order may not be revoked until a determination is made after the hearing that grounds for revocation exist. Executed at El Monte, California, this fl day of October 2003. Alle%fyons, Chief Mobile Source Operations Division B&B FABRICATION, INC.—CORVETTE EXHAUST HEADER—D—506—2


Document Created: 2005-09-01 12:40:49
Document Modified: 2005-09-01 12:40:49

Previous E.O. D-506-1 | Previous E.O. D-505 | Next E.O. D-506-3 | Next E.O. D-507