Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on February 11, 2009.
As of Friday, December 27th, 2024 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModels
61969, 61949, 799492006 and older model year General Motors vehicles equipped with a 4.8, 5.3, 5.7, or 6.0 liter LS1 Gen III engine.

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-215-70
  • Executive Order 215-70 / D215-70
  • ARB # D-215-70
  • Executive Order No: D-215-70
  • C.A.R.B. No. D-215-70
  • Resolution D-215-70
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-215-70 PDF

D-215-70 Document:

CARB_D-215-70

State of California AIR RESOURCES BOARD EXECUTIVE ORDER D—215—70 Relating to Exemptions Under Section 27156 of the Vehicle Code EDELBROCK CORPORATION CYLINDER HEADS Pursuant to the authority vested in the Air Resources Board by Section 27156 of the Vehicle Code:; and Pursuant to the authority vested in the undersigned by Section 39515 and Section 39516 of the Health and Safety Code and Executive Order G—02—003; IT IS ORDERED AND RESOLVED: That the installation of the Edelbrock/Lingenfelter Performer RPM General Motors Gen II! Cylinder Heads (P/N 61969), RPM Xtreme LS Series Cylinder Heads (P/N 61949), Performer LT1 Cylinder Heads (P/N 61909), and RPM Xtreme CNC Cylinder Heads (P/N 61939), marketed and manufactured by the Edelbrock Corporation, 2700 California Street, Torrance, California, 90503 has been found not to reduce the effectiveness of the applicable vehicle pollution control system and, therefore, is exempt from the prohibitions of Section 27156 of the Vehicle Code for the following vehicle applications: Part No. Application 61969, 61949 2006 and older model year General Motors vehicles equipped 79949 with a 4.8, 5.3, 5.7, or 6.0 liter LS1 Gen III engine. 61909, 61905, 1997 and older model year General Motors vehicles equipped with a 61918 5.7L LT—1 engine. $1939 1997 and older model year General Motors vehicles equipped with a 5.7L LT—1 or LT—4 engine. This Executive Order is valid provided that the installation instructions for the Edelbrock/Lingenfelter Performer RPM General Motors Gen III Cylinder Heads, RPM Xtreme LS Series Cylinder Heads, Performer LT1 Cylinder Heads, and RPM Xtreme CNC Cylinder Heads will not recommend tuning the vehicle to specifications different from those of the vehicle manufacturer. Changes made to the design or operating conditions of the Edelbrock/Lingenfelter Performer RPM General Motors Gen III Cylinder Heads, RPM Xtreme LS Series Cylinder Heads, Performer LT1 Cylinder Heads, and RPM Xtreme CNC Cylinder Heads, as exempt by the Air Resources Board, which adversely affect the performance of the vehicle‘s pollution control system shall invalidate this Executive Order. Marketing of the Edelbrock/Lingenfelter Performer RPM General Motors Gen III Cylinder Heads, RPM Xtreme LS Series Cylinder Heads, Performer LTA1 Cylinder Heads, and RPM Xtreme CNC Cylinder Heads using any identification other than that shown in this Executive Order or marketing

z. of the Edelbrock/Lingenfelter Performer RPM General Motors Gen III Cylinder Heads, RPM Xtreme LS Series Cylinder Heads, Performer LT1 Cylinder Heads, and RPM Xtreme CNC Cylinder Heads for an application other than those listed in this Executive Order shall be prohibited unless prior approval is obtained from the Air Resources Board. Exemption of the Edelbrock/Lingenfelter Performer RPM General Motors Gen III Cylinder Heads, RPM Xtreme LS Series Cylinder Heads, Performer LT1 Cylinder Heads, and RPM Xtreme CNC Cylinder Heads shall not be construed as exemption to sell, offer for sale, or advertise any component of the kit as an individual device. This Executive Order does not constitute any opinion as to the effect the use of the Edelbrock/Lingenfelter Performer RPM General Motors Gen III Cylinder Heads, RPM Xtreme LS Series Cylinder Heads, Performer LT1 Cylinder Heads, and RPM Xtreme CNC Cylinder Heads may have on any warranty either expressed or implied by the vehicle manufacturer or the Edelbrock Corporation. This Executive Order is granted based on submitted OBD II test data on a 1996 Impala with the Performer LT1 Cylinder Heads installed and previously submitted emission test data in support of Executive Order D—215—66. In addition to the foregoing, the Air Resources Board reserves the right in the future to review this Executive Order and the exemption provided herein to assure that the exempted add—on or modified part continues to meet the standards and procedures of Title 13, California Code of Regulations, Section 2222, et seq. THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF ANY CLAIMS OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF EDELBROCK CORPORATION‘S CYLINDER HEADS. No claim of any kind, such as "Approved by the Air Resources Board", may be made with respect to the action taken herein in any advertising or other oral or written communication. Violation of any of the above conditions shall be grounds for revocation of this order. The order may be revoked only after a ten—day written notice of intention to revoke the order, in which period the holder of the order may request in writing a hearing to contest the proposed revocation. If a hearing is requested, it shall be held within ten days of receipt of the request and the order may not be revoked until a determination is made afierthe hearing that grounds for revocation exist. Executed at El Monte, California, this I day of February 2009. W%«%f Annette Hebert, Chief Mobile Source Operations Division FDFI BROCK CORPORATION — CYI INNFR HFANS — n—215.70


Document Created: 2017-09-06 13:24:51
Document Modified: 2017-09-06 13:24:51

Previous E.O. D-215-69 | Previous E.O. D-214 | Next E.O. D-215-71 | Next E.O. D-216