Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on June 11, 1992.
As of Sunday, December 22nd, 2024 this Executive Order has not been overturned or superceeded.

Approved Parts

Models
1990-1992 Ford Mustang powered by a 302 CID (5.0 L) V8 gasoline engine

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-225-20
  • Executive Order 225-20 / D225-20
  • ARB # D-225-20
  • Executive Order No: D-225-20
  • C.A.R.B. No. D-225-20
  • Resolution D-225-20
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-225-20 PDF

D-225-20 Document:

CARB_D-225-20

(Page 1 of 2) State of California AIR RESOURCES BOARD EXECUTIVE ORDER D—225—20 Relating to Exemptions Under Section 27156 of the Vehicle Code CRANE CAMS, INC. FORD INTERCEPTOR DOWNSTREAM ENGINE MANAGEMENT .SYSTEM Pursuant to the authority vested in the Air Resources Board by Section 27156 of the Vehicle Code; and Pursuant to the authority vested in the undersigned by Sections 39515 and 39516 of the Health and Safety Code and Executive Order §—45—5; IT IS ORDERED AND RESOLVED: That the installation of the Ford Interceptor Downstream Engine Management System (Interceptor) manufactured by Crane Cams, Inc. of 530 Fentress Bivd., Daytona Beach, FL 32114 has been found not to reduce the effectiveness of the applicable vehicle pollution control system and, therefore, is exempt from the prohibitions of Section 27156 of the Vehxcle Code for 1990 to 1992 Ford Mustangs powered by a 302 CID (5.0L) V—8 gasoline engxne. This Executive Order is valid provided that the installation instructions for the Interceptor will not recommend tuning the vehicle to specifications different from those submitted by Crane~Cams, Inc. Cfianges made to the design or operat1ng conditions of the Interceptor, as empt by the Air Resources Board, which adversely affect the performance of Iveh1cle s pollut1on control system shall 1nva11date thxs Executtve Order. Market1ng of the Interceptor using any 1dent1f1cat1on other than that shown in this Executive Order or marketing of the Interceptor for an application other than those listed in this Executive Order shall be prohibited unless prior approval is obtained from the Air Resources Board. Exemption of the Interceptor shall not be construed as exemption to sell, offer for sale, or advertise any component of the kit as an individual device. This Executive Order does not constitute any opinion as to the effect that the use of the Interceptor may have on any warranty either expressed or 1mp1ied by the vehicle manufacturer. This Executive Order is granted based on results from emissions tests conducted in accordance with Cold—Start CVS—75 Federal Test Procedure. However, the ARB finds that reasonable grounds exist to believe that use of the Interceptor may adversely affect emissions of motor vehicles when cperating under conditions outside the parameters of the previously prescribed test procedures. Accordingly, the ARB reserves the right to conduct additional emission tests, in the future, as such tests are developed, that will more adequately measure emissions from all cycle phases. If such test results demonstrate that the Interceptor adversely affects emissions during off—Cycle conditions {deff®@# as those—conditions

CRANE CAMS, INC. EXECUTIVE ORDER D—225—20 INTERCEPTOR c {Page 2 of 2) which are beyond the parameters of the Cold—Start CYS—75 Federal Test Procedure), this Executive Order shall be effectively rescinded as of the date the test results are validated. Further, if such test results or other evidence provides the ARB with reason to suspect that the Interceptor will affect the durability of the emission control system, Crane Cams, Inc. shall be required to submit durability data to show that the durability of the vehicle emission control system is not, in fact, affected and/or that the add—on or modified part demonstrates adequate durability. In addition to the foregoing, the ARB reserves the right in the future to review this Executive Order and the exemption provided herein to assure that the exempted add—on or modified part continues to meet the standards and procedures of Title 13, California Code of Regulations, Section 2222, et seq. i . THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF CLAIMS OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF CRANE CAMS‘ INTERCEPTOR. No claim of any kind, such as "Approved by the Air Resources Board" may be made with respect to the action taken herein in any advertising or other oral or written communication. Violation of any of the above conditions shall be grounds for revocation of this order. The order may be revoked only after ten day written notice of intention to revoke the order, in which period the holder of the order may request in writing a hearing to contest the proposed revocation. If a hearing is requested, it shall be held within ten days of receipt of the request and the order may not be revoked until a determination after hearing that grounds for revocation exist. — > L. Executed at El Monte, California, this 44 d azy June, 1992. . B. Summerfie Assistant Divistion Chief Mobile Source Division

State of California AIR RESOURCES BOARD EVALUATION OF CRANE CAMS, INC. FORD INTERCEPTOR DOCWNSTREAM ENGINE MANAGEMENT SYSTEM FOR EXEMPTION FROM THE PROHIBITIONS OF VEHICLE CODE SECTION 27156 IN ACCORDANCE WITH SECTION 2222, TITLE 13, OF THE CALIFORNIA CODE OF REGULATIONS June 1992

— State of California AIR RESOURCES BOARD EVALUATION OF CRANE CAMS, INC. FORD INTERCEPTOR DOWNSTREAM ENGINE MANAGEMENT SYSTEM FOR EXEMPTION FROM THE PROHIBITIONS OF VEHICLE CODE SECTION 27156 IN ACCORDANCE WITH SECTION 2222, TITLE 13, OF THE CALIFORNIA CODE OF REGULATIONS by Mobile Source Division State of California Air Resources Board 9528 Telstar Avenue E1 Monte, CA 91731 (This report has been reviewed by the staff of the California Air Resources Board and approved for publication. Approval does not signify that the contents necessarily reflect the views and policies of the Air Resources Board, nor does the mention of trade names or commercial products constitute endorsement or recommendation for use.)

SUMMARY Crane Cams, Inc. has Epp]ied for an exemption from the prohibitions of the Vehicle Code Section 27156 for their Ford Interceptor Downstream Engine Management System (Interceptor) for installation on 1990—92 Ford Motor Company Mustangs, sold in California under AB965, equipped with a 302 HQ (5.0L) V¥—8 gasoline engine. Crane Cams has submitted a completed application and all the required inform;tion, as well as exhaust emissions test data performed at Crane Emissions Laboratory and E.C.S. Laboratories, Inc. . Based on the submitted information ‘and the results of the emissions . tests performed at both laboratories, tfle staff concludes that the installation of Crane Cams‘ Interceptor will not adversely affect exhaust emissions on the sfiecified vehicles when tested in accordance with the Cold Start CVS—75 Federal Test Procedures. l » The staff recommends Crane Cams, Inc. be granted an exemptign as requested and that Executive Order D—225—20 be issued.

Page Number SUMMARY CONTENTS 11 I. INTRODUCTION II. CONCLUSION III. RECOMMENDATION IV. DESCRIPTION OF THE FORD INTERCEPTOR oA DISCUSSION OF THE FORD INTERCEPTOR @op APPENDIX . Software configuration Instailation instructions 11

EVALUATION OF CRANE CAMS, INC. FORD INTERCEPTOR DOWNSTREAM ENGINE MANAGEMENT SYSTEM FOR EXEMPTION FROM THE PROHIBITIONS OF VEHICLE CODE SECTION 27156 IN ACCORDANCE WITH SECTION 2222, TITLE 13, OF THE CALIFORNIA CODE OF c REGULATIONS I. INTRODUCTION Crane Cams, Inc. of 530 Fentress Bivd., Daytona Beach, Florida 32114, has applied for an exemption from the prahibitidns of Vehicle Code Section 27156 for their Ford Interceptor Downstream Engine Managefient System {(Interceptor) for installation on 1990—92 Ford Motor Company Mustangs, sold in California under AB 965, equipped with a 302 (5.0L) Y—8 gasoline engine. Crane Cams has submitted a completed application and all the required information, as well as exhaust emissions test data performéd at Crane Emissions Laboratory and E.C.S. Laborato;ies, Inc. II. CONCLUSIONS Based on the submitted information and the results of the emissions tests performed at both laboratories, the staff concludes that the installation of Crane Cams‘ Interceptorlwi]l not adversely affect exhaust emissions from vehicles for which the exemption is requested when tested in accordance with the Cold Start CVS—75 Federal Test Procedures. III. RECOMMENDATION | The staff recommends that Crane 6ams, Inc. be granted an exemption as requested and that Executive Order D—225—20 bé issued. IV. DESCRIPTIONOFTHEFORDINTERCEPTOR The Interceptor is Qpecifically designed for installation on 1990—92 Ford Motor Company Mustangs that are equipped with a 302 (5.0L) V—8 gasoline engine. The Interceptor is an electronic programmable controller, designed to enhance the vehicle performance without interfering with the emissions —1—

related functions. Certain features of the Interceptor extend the capabilities of the stock control system in the areas of performance and security. | The Interceptor is comprised of three components: an engine controller, a hand—held data terminal, and a wire harness. The ancillary items include a cable to connect the hand—held terminal to the controller and an OWnerIOperator Manual. The hand—held terminal has two windows, allowing access to a LCD display screen and a 20—key, membrane—type keypad for data entry and command selection. The hand—held terminal weighs 280 grams. The wiring harness consists of ihrée connectors and bundles of individually insulated wires covered Qith a protective loom. Two of the connectors mimic those found 1q the stock ECU/Vehicle harness junction. The third connector plugs into the three components modular connector on the controller. . c The Interceptor is installed between tfie stock»ECU (Electronic Control Unit) and the vehicle harness. Of the 44 signél lines present between the vehicle harness and the stock ECU, 20 lines are passed throfigh. 15 lines are monitored, and 9 lTines are intercepted.' "Passed through" means that a given signal line is connected directly from the vehicle harness to the stock ECU without interruption or contact with any other circuit. "Monitored" means that a given signal is unaffected. "Intercepted" means a given signal could be modified. The Interceptor can modify two basic signals: fuel injector pulses and spark out. The fuel injection pulses are modified in three ways. During operation below the factory rpm limit, injector pulse widths may be modified to provide more or less fuel. The second mode of fuel signal modification takes place during what will be termed "extended rpm operation" beyond the —2—

stock fuel cutoff speed. The third way of modifying fuef pulse signals is shutting off the fuel pulses when a user chosen engine speed is reached. Adjustment limits for fuel‘can be set at a maximum of + 24 percent from base setting. The spark out signal is the command sent to the Ford ignition module which then produces a spark. Adjustment Nimits for timing can be set at a maximum of + 20 degrees from base setting. Yariable driving conditions will not allow the use of a fixed minimum and maximum value for fuel injector pulses and spark out. This is why the Interceptor uses a progressive or regressive implementation table which allows the vehicle to operate without experiencing driveabiIify problems. This imp]eméntation table will only allow the vehicle to se;‘specified values which the manufacturer has determined will not affect vehicle driveability even if the minimum.and maximum values are preprogrammed. See Appendix A for implementation va]des. ‘ The Interceptor also provides the user }nformation about the operation of the engine and the operation of the Intercebtor itseIf. These functions display data on the LCD screen when the Interceptor is in the “mgnitor mode." The engine information functions displaythe current values of engine speed (in rpm), throttle opening (in %)., oxygen sensor state (R or L), fuel pulse duty cycle (in %), and total spark advance (in degrees). These data items are updated with a frequency of about 10 Hz (10 times a second), and thus reflects essentially "real—time" values. | The Interceptor provides user interface through the LCD display and keyboard of the hand—held terminal, and.software which directs the user‘s inputs and reports the status of the Interceptor. There are three modes of operation: system setup, monitor, and data set editing. Setup requires initial inputs of engine cylinders, type of air flow measurement (Mass 3

Air/Speed Density), and injector scheme (bank/simultaneous/sequential). The monitor allows the user to view real—time values of important engine control signals. Ohce the interceptor is programmed with the necessary system setup data, the monitor mode becomes the default screen during normal vehicie operation. Data set editing allows the user to make adjustments to any of the three available data sets without destroying previously saved data. v.— THE A 1991 Ford Mustang (AB 965) powered by a 302 CID engine was used for the evaluation of the Interceptor. Emission tests conducted by CEane Emissions Laboratory consisted of four cold—start CVS—75 emission tests with the Interceptor installed on the test vehicle. The four cold—starts were used by Crane and ARB to determine worst case emission parameters of the Interceptor. The résults were evaluated against the emission standards as demonstrated in Table 1. Table 1 CVS—75 TEST RESULTS (Crane Emissions Laboratory) HC £0 NOx Emission standards 0.41 3.4 1.0 #1 +24% fuel —20 degrees spark 0.18 2.00 0.47 #2 —24% fuel +20 degrees spark 0.15 0.29— 0.78 #3 +24% fuel +20 degrees spark 0.20 2.35 0.57 #4 —24% fuel —20 degrees spark 0.13 0.39 0.61

The ARB also required Crane fo conduct two additional CVS—76 emissions tests, test #2 & #3 as described in Table 1, at an ARB recognized independent laboratory. Véhicle exhaust emissions in the two modified configurations were compared with the applicable emission standards. These results are shown in Table 2. Table 2 CVS—75 TEST RESULTS ECS Laboratories, Inc. HG cQ _ NQx Emission standards G.41 > 3.4 1.0 #1 —24% fuel +20 degrees spark 0.21 0.33° 0.86 #2 +24% fuel +20 degrees spark 0.22 1.26 Q0.77 Difference #1 | ~0.20 —3.07 —0.14 Difference #2 — —0.19 —2;14—-0.23 Both CVS—7§ emissions test results at Crane Emissions Laboratory and ECS Laboratories, Inc. indicate that HC, CO and NOx emissions of the vehicle with the Interceptor insta1led,afe below the emission standards. This demonstrates that the installation of the Interceptor for 1990 to 1992 Ford Mustangs equipped with a 302 CID (5.0L) V—8 gasoline engine will not adversely affect exhaust emissions when tested in accordance with the Cold Start CVS—75 Federal Test Procedures. | Crane Cams has submitted all the required information and fulfilled the requirements for an exemption. The test results confirmed that Crane Cams‘ Interceptor meets the requirements for the exemption. —5—

APPENDIX

Mode: Load RPM Adjustment Limits Fuel Spork Min Max Min Max Idie N/A N/A —20% +10% —40 +460 |Part_Throttle Low <2200 —16% +10% —40 440 .. : Mid <2200 —16% +10% —40 440 High <2200 —16% +10% —40 +408 NorivangI4N03 IuyMi40s Low 2200—4000 —24% +24% —20° +200 |_— Mid ° _|2200—4000] —24% +24% —20° +20° High 2200—4000 —24% +24% —20° +20° Low 4000—5800 —24% +24% _ —200 +200 Mid 4000—5800| —24%: +24% ‘—20° +200 High 4000—5800| —24% +24% —20° . +20° _| WwOT N/A <2200 —24% +24% —20° +200 . N/A 2200—4000 —24% +24% —20° +20° N/A 4000—5800 —24% +24% —20° +200

Unpack the Interceptor, noting the four components: the controller (metal box), the Hand—Held Terminal (plastic hax), the harness (black), and the data cable (gray or beige}.You will need the following hand tools to install your X Interceptor: wrenches of 7/16",10mm and 7mm sizes, a medium—size Phillips screwdriver, a small fiat acrewdriver, and a razor blade or knife. Proceed with the installation in the steps shown below. Cramen N ie ‘ Step 2: Remove the one f Phill )..‘pflund " jamb

P Step 7: Place the vehicle hamess/Interceptor hamess pair under the Step 8: Routs the mnalnm of the Interceptor harness under the carpeting in the passanger footwell. Relnxfn.ll the stock computer in its cflmoflnqflmgmm .h&mga-a inch silt in the carpet as original tion, locating. it with the plastic cage.. Replace the cage shown and. the hamess through the siit and under the seat. Leave ; : the edge of the carpetalong the sif exposed until Step #1 Step 9t Leadthe end of the hamesa under the seat and out between ° top P ler the seat, rotaling !t so the Data the front two seat posts. Connect the datr cable to the Interceptor Cable paints toward the driver.. It fite anugly in the depression under the controller and tighten the twa anchor screws. Connect the controller to seat —panel caver and replace the screws. and the hamess using the three black push—dock connectors. the exposed carpet edge back and tighten the screws. Step 12; " Find & convenient spot for the Kand—Hald Terminal. Aesunrsnsnepabieieeemical. You‘ are ow reacy io DO NOT ATTEMPT TO START YOUR VEHICLE! Proceed to the next page to learn —more about the interceptor.


Document Created: 2005-09-01 12:42:55
Document Modified: 2005-09-01 12:42:55

Previous E.O. D-225-19 | Previous E.O. D-224 | Next E.O. D-225-21 | Next E.O. D-226