Approval Details

Valid E.O.

Validity

This Executive Order approved the specified parts on on February 2, 1995.
As of Monday, October 7th, 2024 this Executive Order has not been overturned or superceeded.

Approved Parts

Part NumberModelsModification
11802-161994 & Older GM V-8, 262-400 C.I.D. , excluding the GM 4.6L1.6 Ratio 3/8" stud dia

This Executive Order may be listed as:
  • C.A.R.B.E.O. D-225-50
  • Executive Order 225-50 / D225-50
  • ARB # D-225-50
  • Executive Order No: D-225-50
  • C.A.R.B. No. D-225-50
  • Resolution D-225-50
For Free CARB Executive Order Status verification, email an image of the device Executive Order label as well as the Year/Make/Model and Test Group # of the vehicle to [email protected]

Download: Executive Order D-225-50 PDF

D-225-50 Document:

CARB_D-225-50

(Page 1 of 2) State of California AIR RESOURCES BOARD EXECUTIVE ORDER D—225—50 Relating to Exemptions Under Section 27156 of the Vehicle Code CRANE CAMS, INC. ROCKER ARMS Pursuant to the authority vested in the Air Resources Board by Section 27156 of the Vehicle Code; and Pursuant to the authority vested in the undersigned by Sections 39515 and 39516 of the Health and Safety Code and Executive Order G—45—5; IT IS ORDERED AND RESOLVED: That the installation of the rocker arms manufactured by Crane Cams, Inc. of 530 Fentress Blvd., Daytona Beach, Florida 32114 has been found not to reduce the effectiveness of the applicable vehicle pollution control system and, therefore, is exempt from the prohibitions of Section 27156 of the Vehicle Code for all 1994 and older General Motors vehicles equipped with a V8 gasoline engine as listed in Exhibit A, excluding the GM 4.6L engine. This Executive Order is valid provided that installation instructions for these rocker arms will not recommend tuning the vehicle to specifications different from those submitted by the vehicle manufacturer. Changes made to the design or operating conditions of the rocker arms, as exempt by the Air Resources Board, which adversely affect the performance of h a vehicle‘s pollution control system shall invalidate this Executive Order. Marketing of these rocker arms using any identification other than that shown in this Executive Order or marketing of these rocker arms for an application other than those listed in this Executive Order shall be prohibited unless prior approval is obtained from the Air Resources Board. This Executive Order does not constitute any opinion as to the effect the use of the camshaft may have on any warranty either expressed or implied by the vehicle manufacturer. THIS EXECUTIVE ORDER DOES NOT CONSTITUTE A CERTIFICATION, ACCREDITATION, APPROVAL, OR ANY OTHER TYPE OF ENDORSEMENT BY THE AIR RESOURCES BOARD OF CLAIMS OF THE APPLICANT CONCERNING ANTI—POLLUTION BENEFITS OR ANY ALLEGED BENEFITS OF CRANE CAMS‘ ROCKER ARMS. No claim of any kind, such as "Approved by the Air Resources Board" may be made with respect to the action taken herein in any advertising or other oral or written communication.

CRANE CAMS, INC. EXECUTIVE ORDER D—225—50 (Page 2 of 2) Violation of any of the above conditions shall be grounds for revocation of this order. The order may be revoked only after ten day written notice of intention to revoke the order, in which period the holder of the order may request in writing a hearing to contest the proposed revocation. If a hearing is requested, it shall be held within ten days of receipt of the request and the order may not be revoked until a determination after hearing that grounds for revocation exist. Executed at El Monte, California, this of February, 1995. ssistant Division Chief Mobile Source Division

EXHIBIT A Steel Stud—Mount Rocker Arms Application Description Crane PN GM PN GM V—8 262—400 CID 1.6 Ratio 3/8" stud dia 11802—16 GM V—8 262—400 CID 1.5 Ratio (8 each) and 1.6 Ratio 11803—16 (8 each) 3/8" stud dia GM V—8 262—400 CID 1.6 Ratio Roller Tip 3/8" stud dia 11807—16 Die—Cast Aluminum Stud—Mount Rocker Arms Application Description Crane PN GM PN GM V—8 262—400 CID 1.6 Ratio 3/8" stud dia 11746—16 GM V—8 262—400 CID 1.6 Ratio 7/16" stud dia 11747—16 Extruded Aluminum Stud—Mount Rocker Arms Application Description Crane PN GM PN GM V—8 262—400 CID 1.6 Ratio Narrow Body, 10758—16 Self—Aligning, 3/8" stud dia GM V—8 262—400 CID 1.6 Ratio Narrow Body 3/8" stud- dia 10759—16 GM V—8 262—400 CID 1.6 Ratio 3/8" stud dia 11759—16 GM V—8 262—400 CID 1.6 Ratio 7/16" stud dia 11755—16 12361322 GM V—8 262—400 CID 1.6 Ratio 7/16" stud dia 11768TR—16 GM V—8 262—400 CID Variable Ratio (1.5, 1.55, 1.6) 3/8" 11778—16 stud dia GM V—8 262—400 CID Variable Ratio (1.5, 1.55, 1.6) 3/8" 11779—16 stud dia GM V—8 262—400 CID Variable Ratio (1.5, 1.55, 1.6) 7/16" 11780—16 stud dia ARB11.00C (CHRIS YOHPE)

EXHIBIT A Extruded Aluminum Stud—Mount Rocker Arms Application Description Crane PN GM PN GM V—8 262—400 CID Variable Ratio (1.5, 1.55, 1.6) 7/16" 11781—16 stud dia GM V—8 262—400 CID 1.6 Ratio Left and Right Exhaust 11770TR—16 7/16" stud dia GM V—8 262—400 CID 1.6 Ratio Left 7/16" stud dia 11770L—1 GM V—8 262—400 CID 1.6 Ratio Right 7/16" stud dia 11770R—1 GM V—8 262—400 CID 71.6 Ratio Left 7/16" studdia 11766L—1 GM V—8 262—400 CID 1.6 Ratio Right 7/16" stud dia 11766R—1 GM V—8 262—400 CID 1.6 Ratio Left 7/16" stud dia 11762L—1 GM V—8 262—400 CID 1.6 Ratio Right 7/16" stud dia 11762R—1 GM V—8 396—454 CID 1.8 Ratio 7/16" stud dia 13755—16 GM V—8 396—454 CID 1.8 Ratio 7/16" stud dia 13768TR—16 Aluminum Pedestal—Mount Rocker Arms Application Description Crane PN GM PN GM V—8 262—400 CID 1.6 Ratio Intake Offset Left 11734L—1 GM V—8 262—400 CID 1.6 Ratio Intake Offset Right 11734R—1 GM V—8 262—400 CID 1.55 Ratio Exhaust Offset Left 11737L—1 GM V—8 262—400 CID 1.55 Ratio Exhaust Offset Right 11737R—1 GM V—8 262—400 CID 1.6 Ratio Exhaust Offset Left 11738L—1 GM V—8 262—400 CID 1.6 Ratio Exhaust Offset Right 11738R—1 ARB11.00C (CHRIS YOHPE)

EXHIBIT A Aluminum Shaft—Mount Rocker Arms Application Description Crane PN GM PN GM V—8 396—454 CID 1.75 Ratio Intake Offset Left 13732L—1 GM V—8 396—454 CID 1.75 Ratio Intake Offset Right 13732R—1 GM V—8 396—454 CID 1.8 Ratio Intake Offset Left 13733L—1 GM V—8 396—454 CID 1.8 Ratio Intake Offset Right 13733R—1 GM V—8 396—454 CID 1.8 Ratio Exhaust 13739—1 ARB11.DOC (CHRIS YOHPE})


Document Created: 2005-09-01 12:44:37
Document Modified: 2005-09-01 12:44:37

Previous E.O. D-225-49 | Previous E.O. D-224 | Next E.O. D-225-51 | Next E.O. D-226